ALL serving webpages at the rate of almost 3 million hits a month for the past 4 months. Plus it's a lot of work to reiinstall webmin on a working server with more than one site. install one of their products and it's the others fault when parts of it do not work.. I was having fun trying to figure this out... have a peek at this web-site
I understand that I can withdraw my consent at any time. But I don't use names, only IP addresses. Because i usually do this to check my ip address i use this website Log in or register to post comments #11 Wed, 01/13/2010 - 14:07 (Reply to #10) perill I'm no expert on that here- but remove the complexities then add in services and settings one at a time.
Password Linux - Newbie This Linux forum is for members that are new to Linux. You seem to have CSS turned off. These nslookups prove it. I say that because even if I run bind my machine will not use it to resolve any addresses unless I set it as the nameserver .
Like any side effects for this connection switch? AS per the DHCP thing, I would do it, but I fear I'd have to change all the network settings for that: the router is rather sensible and all the PCs Hope this helps Associate in Applied Science - Network Systems Management -Trident Technical College Back to top #3 fantasy09 fantasy09 Topic Starter Members 70 posts OFFLINE Gender:Female Local time:02:50 PM If you are using it purely as a load balancer in one-arm mode then disabling L3 IP forwarding mode might solve the problem.
I have it too with my new tablet. and I finally discovered what the problem was... It is strange. https://sourceforge.net/p/webadmin/bugs/2838/ Visit the following links: Site Howto | Site FAQ | Sitemap | Register Now If you have any problems with the registration process or your account login, please contact us.
Please, any help or hint to troubleshoot this issue. Does your router have a valid DNS configuration? Introduction to Linux - A Hands on Guide This guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started what dns settings are your working client PCs using?
hahaha Side message.... https://forums.freebsd.org/threads/49448/ Search this Thread 10-31-2003, 09:48 PM #1 aluminum LQ Newbie Registered: Oct 2003 Posts: 6 Rep: ERROR: Failed to lookup IP address for (domain name) I've been trying to Please don't fill out this field. aluminum View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by aluminum 11-02-2003, 11:24 AM #4 DavidPhillips LQ Guru Registered: Jun 2001 Location:
For details and our forum data attribution, retention and privacy policy, see here http://3swindows.com/failed-to/failed-to-lookup-view-error-in-views-directory-node-js.html my box is a co-lo and this is a new install of fc4... (they did it) iptables are off and the following is what nmap said: (The 1661 ports scanned but can you visit other websites ? This book contains many real life examples derived from the author's experience as a Linux system and network administrator, trainer and consultant.
If it is already listed as a program allowed to access the network, try removing it from the list and adding it again. I should probably get a degree in computer sciences............... Started by fantasy09 , Mar 28 2014 10:10 AM Page 1 of 3 1 2 3 Next Please log in to reply 35 replies to this topic #1 fantasy09 fantasy09 Members Source Here is the nslookup printouts... # nslookup www.yahoo.com ;; Got referral reply from my.ip.add.res, trying next server ;; Got referral reply from 127.0.0.1, trying next server ;; connection timed out; no
Ping request could not find host google.com. But seriously, thanks for the help, is there anything else I should know? This error is most often caused by having no connection to the Internet or a misconfigured network.
User contributions on this site are licensed under the Creative Commons Attribution Share Alike 4.0 International License. Have followed your instrucions - and checked them - but unfortunately with no positive result. If you are using the Load balancing feature then this works at Layer 4 (or higher if its a content switching LB)so turning Layer 3 mode off would not effect traffic Still the same problem.
Sometimes, we only search for the small grain of sand in the distance, but we are not able to see the tree that stands in front of us... I am running a fc4. Can you confirm your resolv.conf file? have a peek here I did try to change the DNS in IP settings to 192.168.0.1, to no avail.
This is my current setup: Internet -> Router (192.168.0.1) -> ClearOS Server (192.168.0.110) I can reach the webconfig without issues from this PC, with IP: 192.168.0.99. But when I launch "route-n" I get command not found. At the moment, we have just 3 virtual servers and all traffic that is supposed to go through NetScaler is HTTPS traffic. Error code: DNS_PROBE_FINISHED_BAD_CONFIG Resultsof MIni Toolbox MiniToolBox by Farbar Version: 23-01-2014 Ran by Chiquita (administrator) on 28-03-2014 at 10:31:26 Running from "C:\Users\Chiquita\Downloads" Microsoft Windows 7 Home Premium
Let me explain that I am no expert when it comes to command line... Yes No Additional feedback? 1500 characters remaining Submit Skip this Thank you! This error is most often caused by having no connection to the Internet or a misconfigured network. Please refer to our Privacy Policy or Contact Us for more details You seem to have CSS turned off.
Any clues in /var/log/system? Sign up for the SourceForge newsletter: I agree to receive quotes, newsletters and other information from sourceforge.net and its partners regarding IT services and products. DNS lookup failed? Like any side effects for this connection switch?
Unable to Reach an IP Address If host name resolution occurs successfully, the problem might lie elsewhere. The reply is currently minimized Show Accepted Answer George Clarkson Offline Monday, March 05 2012, 10:12 PM - #Permalink Resolved 0 votes Tim Burgess wrote: Hmm looks ok, can you try I am not Complaining or bad talking ANYONE or thing.. hahaha maybe cuz it was us who made it do what it is doing or not doing.
philsown View Public Profile View LQ Blog View Review Entries View HCL Entries Visit philsown's homepage! Actually the solution of the fail to register error I was facing was due to the router configuration, and especially to the MAC address rules. i still have my TI-99-4A! what dns settings are your working client PCs using?